您好，歡迎來到肇慶市鳳翔餐飲設備有限公司！
19927065609
0758-6831629
您好，歡迎來到肇慶市鳳翔餐飲設備有限公司！
19927065609
0758-6831629
This type of machine is specialized in vegetable and cormcutting. It is easily operating for woman. It is also the necessary facility for restaurants and second processing factories. Instantaneous ability is above 15 people. This machine will let you have satisfied feeling.
A. Processing material
Potatoes, carrots, melons, bamboos, onions, apples, vegetables and so on.
B. Processing dimension:
（standard）
H 10. 15. 20mm cubes or bars.
L T （special dimension）
3-20mm cubes or bars.
C. Capacity
15/mm cubes; 1000kg/hr
D. Voltage
3 phase / 415V, 50Hz / 4P / 0.75KW
（each countries has different voltage connection）
E. Machine dimension & weight
L 800×W 700×H 1260mm
F. Cutting work outline
Connecting “ON” switch, add little water when machine is running and put suitable amount of material to the machine. （Material diameter under 8/cm）. Leaf blade will turn over the material to the fixed thickness of the place of flate cutter. And crosscut cutter will cut the bars into cubes and flow down to the machine after round cutter cuts material into bars. Easily operate, and processing material is clean and delicacy.
G. Voltage connection
Power: 3 phase / 415V / 4P / 0.75KW. Connect power cord （red, black, white） when use the machine. Then connect （green） line to insurance after that start to operating.
B
A
（1） The power line A connected to power supply. （Attention the motor shift）
（Attention 4 power lines, green for the grounding line.）
（2） Water pipeline will be connected B, then the installation is completed.
H. Installing location
Consider whether the water drains unimpededly or not when install the machine.
I. Watch out the machine running
Make sure there are no foreign objects on the entrance of the machine and inside of the leaf blade after connecting voltage to avoid the cutter broken while the machine running. Make sure the direction of leaf blade is correct, rith circum gyratoin （clock-wise）.
J. Method of adjusting thickness of flate cutting
The standard allocation method as follows: （if cut cube is formed by three Cutter）
（1） The first knife （cutting thickness）: Plane broadswords Z. （Adjustable by cutting thickness）
（2） The second knife （cutting width）: Circular knife Group Y.
5mmP （space）: 5mm
10mmP （space）: 10mm
15mmP （space）: 15mm
20mmP （space）: 20mm
（3） The third knife （cut length）: transverse plane knife Group.
5mm uses 15 knife group
10mm uses 8 knife group
15mm uses 6 knife group
20mm uses 4 knife group
K. Method of adjusting aluminum fence
Aluminum fence feeds material to crosscut cutter when round cutter cuts the material. This is why the sharp place of aluminum fence has to get close to the cushion of gap of round cutter or the dimension of aluminum fence marks on the bottom right side.
L. Round cutter discharging
Round cutter dimension drawing
Round cutter dimension
Standard （mm）
P: 10
P: 15
P: 20
Special （mm）
P: 3-20
（1） Avert black screw of fixed eccentric axis.
（2） Pull down the fixed bolt of round cutter eccentric axis. Then round cutter can be discharged.
（3） 
Fix the u-shape spanner on the round cutter set, then loosen sexangular on the round cutter axis （two sides of 24m/m spanner）, then it can be taken out.
M. Crosscut cutter discharge
Crosscut cubes round piece
5m/m uses 21 pieces
10m/m uses 8 pieces
15m/m uses 6 pieces
20m/m uses 4 pieces
（1） Fix u-shape spanner on the fixed crosscut cutter set when discharge crosscut cutter. Then loosen sexangular screw （24m/m spanner）, then it can be taken out.
N. Daily cleansing
Clean the machine after finish the jobs. Run the machine while operating, then wash it by flush water to clean the leavings.
O. Standard by-products:
Spanner 10, 19, 24………….3
Screwdriver （-）, （+）……….……………2
U-shape spanner 1 PCS
Lubricant oil 1
Tool box 1 box
微信公眾號-關注我們最新動態(tài)